| Whakatakotoranga | Awhe, Kōwhiringa ranei |
| Mātotoru | 0.2mm ki te 250mm |
| Whānui | 500 mm ki 2500 mm |
| Te roa | 1000 mm ki 12000 mm |
| Te riri | O, H111, H32, me etahi atu (H12 ki H38) |
| Maimoatanga Mata | Te huri, whakakorikori, paraihe, anodizing, etc. |
Ko nga konumohe konumohe e mohiotia ana mo o raatau kaha me te kaha-ki-taimaha, ka waiho hei whiringa rongonui puta noa i nga momo ahumahi. I roto i enei koranu, te 5454 Ko te Pereti Rau Aluminium e tu ana mo tona kaha teitei, tino pai te aukati waikura, me te ahua pai ake. Ka rukuhia e tenei tuhinga nga korero motuhake o te 5454 Pereti Rau Aluminium, ona painga, whakaritenga, āhuatanga pūkaha, tono, me etahi atu.
Ko te 5454 Ko te Pereti Rau Aluminium he konumohe-konupora teitei te kaha e whakamahia nuitia ana i roto i nga mahi hanga kaipuke me nga umanga kawe waka.. He rongonui mo tona tino pai te aukati i te waikura, otira ki te wai moana me etahi atu taiao pirau, kia pai mo nga tono moana.
Te hanganga matū o 5454 He mea nui te pereti pepa konumohe mo ona ahuatanga mahi. Anei he wehewehenga taipitopito:
| Huānga Waahanga | Metric Percentage Range |
|---|---|
| Konumohe (Ko Al) | 94.4 – 97.1 % |
| Chromium (Cr) | 0.05 – 0.20 % |
| Te parahi (Cu) | ≤ 0.10 % |
| Te rino (Fe) | ≤ 0.40 % |
| konupora (Mg) | 2.4 – 3.0 % |
| konupora (Mn) | 0.50 – 1.0 % |
| Ētahi atu, ia | ≤ 0.05 % |
| Ētahi atu, katoa | ≤ 0.15 % |
| Silicon (Na) | ≤ 0.25 % |
| Titanium (O) | ≤ 0.20 % |
| Zinc (Zn) | ≤ 0.25 % |
Ko te 5454 Ko te pereti pepa konumohe he maha nga painga e pai ana mo nga tono maha:
Ko te 5454 Kei te waatea te pereti pepa konumohe i roto i nga momo matotoru, whanui, me te roa, a ka taea te tuku i roto i nga ahuatanga rereke:
| Whakatakotoranga | Awhe, Kōwhiringa ranei |
| Mātotoru | 0.2mm ki te 250mm |
| Whānui | 500 mm ki 2500 mm |
| Te roa | 1000 mm ki 12000 mm |
| Te riri | O, H111, H32, me etahi atu (H12 ki H38) |
| Maimoatanga Mata | Te huri, whakakorikori, paraihe, anodizing, etc. |
Te maarama ki nga ahuatanga miihini o te 5454 He mea nui te pereti pepa konumohe mo te whakatau i tona pai mo nga momo tono, since the mechanical properties of 5454 alloys of different temperatures vary greatly, taking the O state as an example, the following table shows the mechanical properties of 5454-O:
| Taonga Miihini | Metric Value | Conditions/Comments |
|---|---|---|
| Te pakeke, Brinell | 62 | AA; Tikanga; 500 g load; 10 mm pōro |
| Te pakeke, Knoop | 85 | Converted from Brinell Hardness Value |
| Te pakeke, Vickers | 72 | Converted from Brinell Hardness Value |
| Te Kaha Toka, Mutunga | 248 MPa | AA; Tikanga |
| 41.0 MPa | @ 371 °C / 700 °F | |
| 75.0 MPa | @ 316 °C / 601 °F | |
| 115 MPa | @ 260 °C / 500 °F | |
| 150 MPa | @ 204 °C / 399 °F | |
| 200 MPa | @ 149 °C / 300 °F | |
| 250 MPa | @ -28.0 °C / -18.4 °F | |
| 250 MPa | @ 24.0 °C / 75.2 °F | |
| 250 MPa | @ 100 °C / 212 °F | |
| 255 MPa | @ -80.0 °C / -112 °F | |
| 370 MPa | @ -196 °C / -321 °F | |
| Te Kaha Toka, Tukunga | 117 MPa | AA; Tikanga |
| 29.0 MPa | @ 371 °C / 700 °F | |
| 50.0 MPa | @ 316 °C / 601 °F | |
| 75.0 MPa | @ 260 °C / 500 °F | |
| 105 MPa | @ 204 °C / 399 °F | |
| 110 MPa | @ 149 °C / 300 °F | |
| 115 MPa | @ -80.0 °C / -112 °F | |
| 115 MPa | @ -28.0 °C / -18.4 °F | |
| 115 MPa | @ 24.0 °C / 75.2 °F | |
| 115 MPa | @ 100 °C / 212 °F | |
| 130 MPa | @ -196 °C / -321 °F | |
| Elongation at Break | 25 % | @ 24.0 °C / 75.2 °F |
| 27 % | @ -28.0 °C / -18.4 °F | |
| 30 % | @ -80.0 °C / -112 °F | |
| 31 % | @ 100 °C / 212 °F | |
| 39 % | @ -196 °C / -321 °F | |
| 50 % | @ 149 °C / 300 °F | |
| 60 % | @ 204 °C / 399 °F | |
| 80 % | @ 260 °C / 500 °F | |
| 110 % | @ 316 °C / 601 °F | |
| 130 % | @ 371 °C / 700 °F | |
| 22 % | @ Thickness 1.59 mm / 0.0625 i roto | |
| Modulus of Elasticity | 70.3 GPa | AA; Tikanga; Toharite o te mānukanuka me te kōpeketanga. Compression modulus is about 2% greater than tensile modulus. |
| Notched Tensile Strength | 221 MPa | 2.5 cm width x 0.16 cm thick side-notched specimen, Kt = 17. |
| Ultimate Bearing Strength | 427 MPa | Edge distance/pin diameter = 2.0 |
| Bearing Yield Strength | 165 MPa | Edge distance/pin diameter = 2.0 |
| Tauwehenga Pisces | 0.33 | Estimated from trends in similar Al alloys. |
| Te Kaha ngenge | 120 MPa | @ 5.00e+8 cycles; unnotched R. R. Moore rotating beam |
| Kōwae kutikuti | 26.0 GPa | Estimated from similar Al alloys. |
| Te Kaha Kutikuti | 159 MPa | AA; Tikanga |
This table provides a comprehensive overview of the mechanical properties of the 5454 koranu, including hardness, kaha tensile, whakaroa, modulus of elasticity, me etahi atu, under various conditions and temperatures. Ko te “Conditions/Comments” column provides additional details about the specific test parameters or the nature of the property measurement.
Ko te 5454 Ko te pereti pepa konumohe ka kitea te whakamahi i roto i te whānuitanga o nga tono na tona huinga ahurei o nga rawa:
Ko te pereti pepa konumohe 5454-H32 e whakamahia ana mo nga taika whakamaarama me nga waka taika orohia, te tuku urutau ki nga taiao pirau:
| Taonga | Uara |
| Te Kaha Toka | 276 MPa |
| Te Kaha Tuku | 207 MPa |
| Modulus of Elasticity | 70.3 GPa |
| Elongation at Break | 18%
@Temperature 24.0 °C |
| Te pakeke | 73 Brinell |
Ko te 5454 Ko te pereti pepa konumohe H111 he wera-wera mo te kaha ake me te iti o te ngawari, he pai mo nga hanganga moana me nga oko pehanga:
| Taonga | Uara |
| Te Kaha Toka | 262 MPa |
| Te Kaha Tuku | 179 MPa |
| Modulus of Elasticity | 70.3 GPa |
| Elongation at Break | 14%
@Matotoru 1.59 mm |
| Te pakeke | 70 Brinell |
Ko te 5454 E pereti pepa konumohe, i roto i te ahua annealed, tuku ductility tiketike, me te pai formability:
| Taonga | Uara |
| Te Kaha Toka | 165 MPa |
| Te Kaha Tuku | 65 MPa |
| Modulus of Elasticity | 70 GPa |
| Elongation at Break | 25% |
| Te pakeke | 62 Brinell |
Ko te 5454 Ko te konumohe e mohiotia ana e nga momo paerewa, he iti nei nga rereketanga i roto i nga mahi whakangao, i nga whakangao ranei:
He mea nui ki te tirotiro i te paerewa motuhake e hiahiatia ana mo to tono kia tutuki ai nga rauemi ki nga whakaritenga e tika ana.
Mo etahi atu patai, nga korero taipitopito, ki te whakatakoto ota ranei, whakapā atu ki a Huasheng Aluminium, to pono '5454 Pereti Rau Aluminium’ wheketere me te kaihokohoko. Kua rite ta matou roopu tohunga ki te awhina ia koe me o hiahia konumohe katoa.
Kupu Whakataki 1060 Konumohe……
Kupu Whakataki: Kei Huasheng Al…
Kupu Whakataki konumohe konumohe……
Kupu Whakataki 1070 Konumohe……
Kupu whakataki ki 3004 Konumohe……
Kupu Whakataki Nau mai ki Huas……
Henan Huasheng Aluminium Co., Ltd (HHALU mo te poto), whakapumautia i roto i 2001, kei te Taone o Huiguo, te whakapaipai Aluminium rongonui o Henan Province, He kaihanga ngaio, ka uru ki te rangahau, whanaketanga, whakaputanga, hoko me te ratonga o te pereti pepa konumohe, porowhita konumohe, pepa konumohe, takai konumohe me te porohita konumohe.
I tua atu, Ka hokona ano e HHALU te pereti konumohe mo te hanga me nga kaipuke, pereti whakaata konumohe, me te pereti konumohe miihini miihini.
Nama53, Te huarahi o Dongming, Zhengzhou, Henan, Haina
Mana pupuri © Huasheng Aluminium 2023. Katoa nga mana.
